FORD ESB-M4D145-A-1995 聚乙烯（PE）線狀吹塑塑料

POLYETHYLENE (PE), LINEAR, BLOW MOLDING COMPOUND

ANSI/ASTM F2619:2013 高密度聚乙烯(PE)線管規格

Specification for High-Density Polyethylene (PE) Line Pipe

ASTM F2619/F2619M-07 高密度聚乙烯(PE)線路管道用標準規范

1.1 This specification covers requirements and test methods for high-density polyethylene (PE) materials, pipe and fittings for pressure

Standard Specification for High-Density Polyethylene (PE) Line Pipe

ASTM F2619/F2619M-13 高密度聚乙烯(PE)線路管道用標準規范

1.1 This specification covers requirements and test methods for high-density polyethylene (PE

Standard Specification for High-Density Polyethylene 40;PE41; Line Pipe

FORD WSB-M4D880-A-2006 汽車內部用聚乙烯（PE）線型低密度成型料***與標準FORD WSS-M99P1111-A一起使用***

POLYETHYLENE (PE), LINEAR LOW DENSITY MOLDING COMPOUND, INTERIOR ***TO BE USED WITH FORD WSS-M99P1111-A***

IPC PE-74- 印制板制造和組裝故障排除指南

Trouble Shooting Guide for Printed Board Manufacture and Assembly

RUL PE.3-2002 壓力設備標準規定．規定3：啤酒桶用內裝門（AS 1210的規定

Rulings to pressure equipment Standards - Ruling 3: Internally fitted doors for beer tanks (Ruling to AS 1210)

IPC PE-740A-1997 印制電路板制造和裝配的修訂版A的疑難解答

IPC Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers

Troubleshooting for Printed Board Manufacture and Assembly Revision A

NEMA PE 1-1992 不間斷電源系統

This Standards Publication covers uninterruptible power systems (UPS) as it applies to semiconductor ac to ac converter systems with a dedicated dc

Uninterruptible Power Systems

GMP.PE.003-2011 高密度聚乙烯，擠出級，共聚物第 3 期；請勿在新程序上使用；替換為 GMW16426 GMW16426P-PE-T2

Polyethylene ?High Density, Extrusion Grade, Copolymer Issue 3; Do Not Use on New Programs; Replaced by GMW16426 ?GMW16426P-PE-T2

RUL PE.6-2002 壓力設備標準的規定．規定6：熔焊氯

Rulings to pressure equipment Standards - Ruling 6: Fusion-welded chlorine transport drums (Ruling to AS 1210)

NEMA PE 7-1997 通信型蓄電池充電器

Communication Type Battery Chargers

GMP.PE.060-2011 聚乙烯高密度、抗應力開裂、吹塑第 3 期；請勿在新程序上使用；替換為 GMW16426 - GMW16426P-PE-T1

Polyethylene ?High Density, Stress Crack Resistant, Blow Molding Issue 3; Do Not Use on New Programs; Replaced by GMW16426 - GMW16426P-PE-T1

RUL PE.12-2004 壓力設備標準的規定．規定12：壓力配件的最小公稱厚度（AS 1210－1997

Rulings to pressure equipment Standards - Ruling 12: Minimum nominal thickness of pressure parts (AS 1210-1997)

NEMA PE 1-2012 不間斷電源系統（UPS）的規格和性能驗證

Foreword This standards publication is a NEMA Adoptive Standard based on IEC 62040-3@ Uninterruptible power systems (UPS) ?? Part 3: Method

Uninterruptible Power Systems (UPS) — Specification and Performance Verification